Avital 4108L Guía de instalación

Model 4113Installation GuideNOTE: This product is intended for installation by a profes-sional installer only! Any attempt to install this product by

➢Virtual tachVirtual Tach is a new feature for Directed this year. It is the default RPM-sensing method for new remote start systems. V

11© 2008 Directed Electronics. All rights reserved.Component locations and finding wiresFor detailed information on where to locate components,

12© 2008 Directed Electronics. All rights reserved.➢ Primary harness (H1) wiring diagramH1/1LIGHT GREEN/BLACKFACTORY ALARM DISARMH1/2GREEN/WHITE FACTO

13© 2008 Directed Electronics. All rights reserved.➢ Door lock harness, 3-pin connector1GREEN (-) LOCK OUTPUT *2EMPTY NOT USED3BLUE (-) UNLOCK OUTPUT

14© 2008 Directed Electronics. All rights reserved.Primary harness (H1), 9-pin connectorH1/1LIGHT GREEN/BLACKFACTORY ALARM DISARMThis wire sends a neg

15© 2008 Directed Electronics. All rights reserved.Relay for Positive (+) Disarm WireH1/2GREEN/WHITE FACTORY REARMThis wire sends a negative pulse eve

16© 2008 Directed Electronics. All rights reserved.H1/4WHITE/BLUE (-) ACTIVATION INPUT This input comes from the factory set to 1 activation pulse. Th

17© 2008 Directed Electronics. All rights reserved.H1/6ORANGE (-) GROUND WHEN LOCKED OUTPUTThis wire supplies a (-)500 mA ground as long as the system

18© 2008 Directed Electronics. All rights reserved.H1/8BLACK (-) chassis GROUND connectionWe recommend that you do not use a factory ground.

19© 2008 Directed Electronics. All rights reserved.ming Jumpers section of this guide. P/N 8617 or a standard automo-tive SPDT relay must be used on t

Bitwriters with a date code of 6a or older require an IC upgrade (p/n 998M). Some bitwriters with a date code of 6B do not require the IC upgrade, ref

20© 2008 Directed Electronics. All rights reserved.Heavy gauge relay interfaceThe heavy gauge wires are used to energize high current circuits in the

21© 2008 Directed Electronics. All rights reserved.5PINK/WHITE (+) PROGRAMMABLE OUTPUT FOR ACCESSORY OR IGNITIONConnect this wire to the second igniti

22© 2008 Directed Electronics. All rights reserved.Figure A Figure BImportant! Always use the Vehicle Safety Check section of this guide to verify tha

23© 2008 Directed Electronics. All rights reserved.H2/3BROWN (+) BRAKE SWITCH SHUTDOWN WIREThis wire MUST be connected to the vehicle’s brake light wi

24© 2008 Directed Electronics. All rights reserved.Neutral safety switch interfaceSome vehicles do not have an electrical neutral safety switch. Inste

25© 2008 Directed Electronics. All rights reserved.eral Motors product or a Dodge Dakota pickup, please call Directed Electron ics Technical Support f

26© 2008 Directed Electronics. All rights reserved.Programming jumpers➢Light flash (+)/(-)This jumper is used to determine the light flash output polar

27© 2008 Directed Electronics. All rights reserved.Plug-in program switchThe Program switch plugs into the blue two-pin connector. Tach learning➢ Virt

28© 2008 Directed Electronics. All rights reserved.➢ To learn the tach signalDRW-961. Start the vehicle with the key.2. Within 5 seconds, press a

29© 2008 Directed Electronics. All rights reserved.Remote control learn routineThe system comes with two transmitters that have been taught to the rec

ContentsGovernment Regulations ...5Warning! safety first ...

30© 2008 Directed Electronics. All rights reserved.Ch Function3Reset Features: This resets features all of the security system to the fact

31© 2008 Directed Electronics. All rights reserved.Learn Routine will be exited if:Ignition is turned off.• Program switch is pressed too many times.•

32© 2008 Directed Electronics. All rights reserved.Operating settings learn routineThe System Features Learn Routine dictates how the unit operates. T

33© 2008 Directed Electronics. All rights reserved.4. Release. The Program switch can now be re-leased. You can advance from feature to feature

34© 2008 Directed Electronics. All rights reserved.Features menuThe factory default settings are indicated in bold text in the table be-low.➢ Menu 1Fe

35© 2008 Directed Electronics. All rights reserved.➢ Menu 2Fea-ture # Feature Opt. 1 Opt. 2 Opt. 3 Opt.4 Opt. 5+1 Engine checkingVirtual tachvoltage O

36© 2008 Directed Electronics. All rights reserved.Feature descriptionsThe features of the system are described below with default settings in bold.➢

37© 2008 Directed Electronics. All rights reserved.5 UNLOCK OUTPUT—1, 2 PULSES: This will program the unlock output to one or two pulses. When the dou

38© 2008 Directed Electronics. All rights reserved.(2) Comfort closure 1 - Activates the 20 second timer after the door lock pulse. (3) Comfort Closur

39© 2008 Directed Electronics. All rights reserved.and shuts down. Programmed to the default setting the engine will run for 12 minutes. If the 24 or

40© 2008 Directed Electronics. All rights reserved.to-start period of a diesel motor. When ON the accessory comes on when the wait-to-start output is

41© 2008 Directed Electronics. All rights reserved.➤ Bitwriter®The Bitwriter® has the ability to fine tune certain features of the security system.

42© 2008 Directed Electronics. All rights reserved.Shutdown diagnosticsThe unit has the ability to report the cause of the last shutdown of the rem

43© 2008 Directed Electronics. All rights reserved. led flasHes sHutdown mode 1 System timed out 2 Over-rev shutdown 3 Low or no RPM,

44© 2008 Directed Electronics. All rights reserved.Important: Make sure there is adequate clearance to the front and rear of the vehicle before attemp

45© 2008 Directed Electronics. All rights reserved.TroubleshootingThe starter cranks for six seconds but does not start.• Either the wrong ignition wi

46© 2008 Directed Electronics. All rights reserved.Does the vehicle have an immobilizer? Some immobilizer systems 4. will not allow the vehicle to cra

47© 2008 Directed Electronics. All rights reserved.The vehicle will start and run only for about 10 seconds.• Is the remote start programmed for volta

48© 2008 Directed Electronics. All rights reserved.Wiring quick reference guideORANGE (-) ground when lockedBROWN (-) horn honk outputred 4 pin d2dbit

49© 2008 Directed Electronics. All rights reserved.Wiring quick reference guide continuedORANGE (-) ground when lockedBROWN (-) horn honk outputred 4

5© 2008 Directed Electronics. All rights reserved.Government RegulationsThis device complies with Part 15 of FCC rules. Operation is subject to the fo

52© 2008 Directed Electronics. All rights reserved.N4113L 2008-07Vista, CA 92081www.directed.com© 2008 Directed Electronics—All rights reservedThe co

6© 2008 Directed Electronics. All rights reserved.Warning! safety firstThe following safety warnings must be observed at all times:Due to the complexit

7© 2008 Directed Electronics. All rights reserved.tion immediately and consult with the user to x the problem immediately.After the remote start modu

8© 2008 Directed Electronics. All rights reserved.What is includedThe control module (see diagram)• HX antenna receiver• Two remote transmitters• A

9© 2008 Directed Electronics. All rights reserved.Installation points to rememberImportant: This product is designed for fuel-injected, automatic tran